A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

航天嵌入式软件数组越界缺陷特征研究

根据统计,数组越界是航天嵌入式软件开发过程中出现最多且最容易被遗漏的缺陷类型之一.目前自动化检测数组越界多基于抽象解释、符号执行、程序模型检验等方法,这些方法在误报、漏报、可扩展性等方面的表现依赖于软件及缺陷特征.分析了近三年航天嵌入式软件第三方测试中发现的94个数组越界问题,从缺陷模式和缺陷表现形式两方面分析得出10项航天嵌入式软件数组越界缺陷特征,并提出对设计具体检测方法关键的若干启示.进一步基于这些特征和启示探讨了数组越界检测算法针对中断驱动型程序的改进方向.     

星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真，以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化，建立终端的轨道热分析模型，准确模拟在轨机动，根据典型机动模式、外热流和涂层退化等因素设计了计算工况，得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异，最大可达23.0℃，采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度，甚至不能部分替代二维转动热分析或热试验；光学天线和反射镜的温度控制是制约终端工作的瓶颈，为终端设计合适的避光机动策略，可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

先进战斗机过失速机动大气数据融合估计方法

可控的过失速机动是先进战斗机超机动性能的重要标志，飞机飞行包线的扩大已超出传统的大气数据系统测量范围，可靠的迎角、侧滑角、总压、静压等飞行大气数据是制约先进战斗机过失速机动中飞行控制的关键因素。以中国推力矢量验证机为对象，基于过失速机动飞行试验的数据，开展大气参数估计与验证研究。结合过失速机动的时间与空间特性，研究了基于风速、地速、空速矢量和惯性姿态、导航参数的大气参数融合计算方法；针对过失速大迎角状态下飞机周围气流非定常、模型非线性导致的融合大气参数误差的复杂特性，进一步构建深度神经网络，对机动状态融合迎角、侧滑角的强非线性误差进行拟合。仿真和飞行试验表明：该方法可在大迎角飞行状态下实现主要大气参数的融合估计，过失速机动过程中融合迎角误差优于2.3°，融合得到的大气参数可为过失速大迎角机动飞行控制提供可靠的大气参数状态反馈。     

Topology optimization in lightweight design of a 3D-printed flapping-wing micro aerial vehicle

Topology optimization is an effective method to obtain a lightweight structure that meets the requirements of structural strength. Whether the optimization results meet the actual needs mainly depends on the accuracy of the material properties and the boundary conditions, especially for a tiny Flapping-wing Micro Aerial Vehicle (FMAV) transmission system manufactured by 3D printing. In this paper, experimental and numerical computation efforts were undertaken to gain a reliable topology optimization method for the bottom of the transmission system. First, the constitutive behavior of the ultraviolet (UV) curable resin used in fabrication was evaluated. Second, a numerical computation model describing further verified via experiments. Topology optimization modeling considering nonlinear factors, e.g. contact, friction and collision, was presented, and the optimization results were verified by both dynamic simulation and experiments. Finally, detailed discussions on different load cases and constraints were presented to clarify their effect on the optimization. Our methods and results presented in this paper may shed light on the lightweight design of a FMAV.     

Accurate approximation of in-ecliptic trajectories for E-sail with constant pitch angle

Propellantless continuous-thrust propulsion systems, such as electric solar wind sails, may be successfully used for new space missions, especially those requiring high-energy orbit transfers. When the mass-to-thrust ratio is sufficiently large, the spacecraft trajectory is characterized by long flight times with a number of revolutions around the Sun. The corresponding mission analysis, especially when addressed within an optimal context, requires a significant amount of simulation effort. Analytical trajectories are therefore useful aids in a preliminary phase of mission design, even though exact solution are very difficult to obtain. The aim of this paper is to present an accurate, analytical, approximation of the spacecraft trajectory generated by an electric solar wind sail with a constant pitch angle, using the latest mathematical model of the thrust vector. Assuming a heliocentric circular parking orbit and a two-dimensional scenario, the simulation results show that the proposed equations are able to accurately describe the actual spacecraft trajectory for a long time interval when the propulsive acceleration magnitude is sufficiently small.     

基于梯度提升决策树的量子科学实验卫星光学实验预测

量子科学实验卫星在轨运行期间完成4种光学实验，地面监测人员通过遥测参数阈值判断卫星是否进行光学实验、实验类型及实验结果.这种方法需要预先设定大量阈值，并且这些阈值需要根据在轨卫星重新设定，可扩展性较差.针对以上问题，提出一种基于机器学习的光学实验判别方法，将量子科学实验卫星的光学实验监测任务抽象为机器学习中的多元分类问题，构建分类模型，利用量子科学实验卫星的真实历史遥测数据对模型进行训练，并通过真实实验计划对训练得到的模型进行验证.实验结果表明，本文提出的方法在没有专家先验知识的前提下，判别准确率达到99%，可用于量子科学实验卫星光学实验的实时监测任务.提出的基于机器学习的判别方法具有较强的可扩展性，可应用于卫星在轨运行的其他监测任务.      

基于工厂模式的OSLC数据集成接口设计与实现

复杂软件系统往往由不同地域的研发团队采用不同的开发工具来协同完成，研发过程中存在数据难以集成的问题.基于开放式生命周期协作服务(OSLC)规范来设计软件协同开发数据接口，有利于提高软件协同开发的效率.首次结合工厂模式和OSLC规范设计并实现数据集成接口，将不同工具的数据集成抽象成统一的公共接口，从而采用统一的数据接口和规范实现不同工具的数据集成，有利于优化软件系统体系结构.以符合OSLC规范的Bugzilla缺陷管理系统和Jenkins持续集成工具的集成为例，以面向航天软件系统研发的SunwiseAEM一体化研发管理平台为载体，基于工厂模式设计并实现了符合OSLC规范的数据集成系统，实现了不同工具间的数据集成，提供了一种通用的、可扩展的数据集成方式.     

利用微波探测仪(ATMS)对在轨微波辐射计观测精度的模拟分析

微波辐射计的观测精度及其对数值模式同化应用的影响评估是微波辐射计观测指标设计的重要参考。基于微波探测仪(ATMS)资料,利用三维变分同化系统模拟分析在轨微波辐射计的观测精度指标。针对ATMS观测误差特征,在其观测基础上增加均值为零、标准偏差分别为0.5,1.0,1.5,2.0K的正态随机扰动,进而获得不同精度的观测模拟值序列,然后利用Harris和Kelley的辐射资料偏差订正经验方法订正不同精度的观测资料。偏差订正后,利用三维变分同化模式(WRFDA)直接同化ATMS资料。通过2016年6月6h预报场的同化试验,评估了不同观测精度的模拟资料对数值模式的同化影响。     

某型装备能源电池异常爆破故障分析

对一起因电池设计缺陷引发装备战训失利的故障进行分析,重点对电池工作机理和设计缺陷展开解析,明确故障定位,并对国内外装备弹上不同体系电池的优缺点进行比较,旨在为产品维护保障、国产化科研等工作提供参考。